The maintenance of electric forklift

Electric forklift is more common truck types, as short-distance transport of goods vehicles, regular carrying heavy goods, to a small failure, prolong forklifts life, regular maintenance is necessary, here under the electric YTO rough terrain forklift maintenance skills .

A circuit system

1, check the sensitivity of the control system. Forklift .

2. Check the contact point for wear.

3, check the light signal system, if necessary, replace the bulbs and fuses.

4, check and adjust the ratio of sulfuric acid batteries, cleaning the cell surface, tighten battery terminals.

5. Check lifting, driving and hit carbon pump.

6, insulation and connecting parts whether damaged or loose.

7, the overall circuit dust.

Second, the transmission system

1. Check tire screws and tires .

2. Check and adjust the brake system and joint activities with butter.

3, cleaning rotating bearings, and add lubricant . Electric China rough terrain forklift .

4. Check the automatic gearbox system, for automatic gearbox and replaced the filter.

5, cleaning gear boxes and gear oil change.

Third, the chain assembly

1, check lift chain, cracks, damage.

2, cleaning driving chains, bearings and add lubricant .

3, clean up the lift chain, the chain axis and add lubricant .

Fourth, the hydraulic system

1, if necessary, adjust, clean up the hydraulic oil valve.

2, check the hydraulic pump, oil pipes, fittings and seals, etc. are not leaking.

3, clean up the hydraulic tank, hydraulic oil and clean up the filter change. Manual forklifts .

The use of forklift

Various attachments and more from the short piston cylinder, high pressure hose, hose winder, quick connectors, circular ring, is a dedicated parts and other components. These parts can be cleaned with reference to the general hydraulic parts, and maintenance. Re-attachment should be noted that in addition to the use of oil leaking pipeline system, cracking and other anomalies, but especially the case with the allowable load, lifting height, size and scope of the case with the goods, the width of the run-time, shall strictly according to performance parameters attachments execution, we can not overload, but not partial load. For partial load operation, small tonnage truck with attachments, short partial load range should be within + -150mm.

In forklift spare parts use, paired two goods cross on thick, fork length should be approximately equal. After two forks mounted on the fork, then it should be kept on the same horizontal plane. Must strictly abide by the rules, do not allow overloading or long-distance transport of goods; or again when carrying long objects gravity position can not be determined, to have someone directing, and be careful. Pork on a skewer with a cargo of goods, the fork should be suitable for the load from the width of the fork is inserted beneath the load as deep as possible, with minimal post-mast tilt to stabilize the load after load to prevent sliding, down load, allows a small amount of mast forward in order to secure cargo and out of the fork down. When the job, the fork should be in the form of low-speed to 30 ~ 40mm from the ground is appropriate, should be appropriate to the door frame backward, driving shall be arbitrarily raise or lower the off road rough terrain forklift, may not turn across the slope and driving on the ramp, not allowed to use pallet fork approach unloading; not allowed to use forks directly Scraper dangerous goods and flammable materials such as; not allowed to use a single job or inertial force fork forks goods; better not use round or braking inertia Humping Easy roll goods.

Forklift Safety Accident combustion equilibrium analysis

Internal combustion counterbalanced Lpg Gas Forklift truck is, we often say, it is generally based on diesel or gasoline engine as a power source. Is now being widely used in railway stations, docks, workshops, warehouses, logistics centers and other places, is mechanized loading and unloading, stacking, the ideal distance transport and logistics equipment integrated operations, is the most widely used motor vehicle factory currently has the largest amount of one kind.

According to state departments of enterprises nationwide casualty statistics show that most casualties occur plant transportation accidents, accounting for about 25%. Here are some of the main truck accidents occur:

Forklift accidents occur mainly due to:

(A) violation posts (such as drunk driving, fatigue driving, driving without a license, etc.);

(B) the illegal traffic (such as speeding, indisputable way to grab the line, forced to overtake, rough handling, do not travel by road, do not yield to pedestrians and vehicles, with people traveling, etc.)

(3) "before starting the lookout not seriously thinking decentralized operation, eager to complete the task or the easy way out of bad mental activity;

(D) not serious maintenance, inspection truck, safety devices (steering, braking, speakers, lighting, etc.) is not complete and effective, fuel leakage, excessive tire wear, forklifts ill run;

(Five) after bad sight, depending on the moment than the road listening to the area (such as a narrow channel, eight curved fork, roadside obstacles, etc.) when the driver's blind confidence, not slow down by chapter, dealing with emergency situations without thinking quasi

(Six) downhill, slippery at (rain, wet pavement oiled, smooth surface, steel, etc.) you do not slow down, anxious to fight the direction or the emergency brake, causing skidding or even overturned.

(Seven) wire (including charging wire) aging Popi, fixed is not strong, Ground, bad and people are not cut off the power switch when leaving the truck.

　　 Unlike fixed all terrain forklifts machinery and equipment, random changes in their working environment, working conditions in turn depends on the driver's immediate operation, whether or not it is safe forklift operation almost at the foot of the hands of the best drivers in the truck, which the driver of the truck raised higher than the other operators safety skills requirements. In short, as long as the truck driver to safely operate the technology, to comply with safety rules, according to Zhang travel, civilized comity, usually diligent inspection and maintenance, in order to avoid the occurrence of various types of vehicles injury.

Storage Device Requirements

     Once considered the data storage requirements, mobile devices will face unprecedented challenges. Must Off road forklifts hold the hand-held terminal to reduce desktop systems not previously encountered vibrations and jolts. The rebound of the rotary drive is amazing, many mobile equipment vendors are aware of the problem, they used a double in a fixed manner to ensure the reliability of data storage: 1) to reduce the base bracket and physical shock; 2) Windows CE operating system, the use of Flash technology to store data and programs.
     Relatively common storage is Flash memory, such as disk or PCMCIA FLASH COMPACT FLASH other smaller packaging. Both packaging standards have been widely recognized, and avoid a lot of extra expense. PCMCIA flash memory has now reached 2G storage capacity, to provide sufficient space for the local storage of the mobile device. For example, WINDOWS 2000 1.4G space occupied, those well-known manufacturers and can provide COMPACT FLASH PCMCIA port, so that the system structure can be more flexible to meet the needs of customers.

An intelligent forklift mobile technology: Compare car terminal and handheld terminals

For the use of handheld terminal on the YTO High Mast Diesel Forklift or car terminal, has been controversial. In fact, the prevailing view was that these two technologies in parallel, are all complementary IT solutions. Lightweight, compact handheld terminal can be flexible in dealing with items to play. A hand-held terminal is usually limited display size, computing power, battery charging and replacement, etc. In addition, a number of other minor factors will affect -? Your workers wearing work gloves if it is, then the hand-held terminal will be somewhat inconvenient. A convenient, easy-to-use user interface is also very important factors.
     Vehicle terminal can carry handheld terminal technology advantage and expand its usefulness. The vehicle terminal mounted on lift trucks, truck, trailer, or other industrial vehicles, allowing information workers operate on the move, calling and all the data displayed on the screen. Driven vehicle terminal with standard wireless network 802.1l direct access to the successful implementation of enterprise management system.
     The formation of a virtual office environment on the truck, no matter when, where can directly access enterprise data. To find in the subzero cold environment perishable goods it? How do I know in particular large-scale production plant yield? How to command a large cargo truck transitions work? This is just a smart utility truck to play a few examples. Second, the core of the intelligent truck - truck when the smart vehicle terminal is running, the following points must be taken into account size, display quality, temperature range (and other environmental parameters), wireless access capabilities, power settings, and more. Many traditional business information system design does not take into account the many industrial operations in harsh environmental factors. Many companies are now beginning to realize the problem and started to meet the needs of the market.
     As we mentioned earlier, you want to pass information systems to improve the quality of work. Vehicle terminal must have the desired customer friendly operating performance and very high stability and reliability. Display size, brightness, contrast and overall reading of very critical. Similarly, the keyboard or touch screen input methods must be able to quickly, easily and universal. In addition, operating assistance, real-time data storage, processor driven, wireless network support and other aspects also have to be taken into account.

 

Intelligent truck performance and volume

Running on a Pentium processor system full-screen color display (VGA or better), can provide universal standard applications and programming environments. Also take into account the way the application is installed, vehicle tools, application site and automotive systems. Many manufacturers will be the scope of the application system will be diversity, display size and loading patterns into account, to meet the needs of users and OSHA. Brightness and readability is a very important parameter, the literacy rate in the industry often require more than 300nit display, a large screen is very popular, and thus require devices must expand overall system volume. So on a large screen can understand a little of the goods in any case very clearly. Those manufacturers, depending on the actual needs, in addition to providing general environmental or vehicle conditions applicable compact 8.4 inches VGA monitor, as well as 10.4 inches VGA, 12.1 inches or 15 inches SVGA XGA.
     High tightness improve equipment reliability
     gas powered forklift terminal must be able to adapt to the harsh working environment changing. Dirt, grease, or other contaminants will have a great damage to equipment. A high degree of sealing systems can reduce this impact and ensure stable performance and operating life of the equipment. In like food processing or pharmaceutical refrigeration required or soak in the work environment, NEMA-4 sealed standard equipment is a very important indicator. "Like the same drum airtight" seal standard NEMA-4, you can ensure that the equipment is suitable for indoor and outdoor environment, water, and wind, the impact of sand, rain, snow and other harsh environments.

Image display capability

In practice, production and warehousing, often require frequent small pieces of data transmission - barcode scanner to record the tray number or order number. Obviously this is not the main task of the CPU, the main task is to control the CPU user interface display. Those simple, character-based display is also far from being able to meet the needs. The graphical Lpg Gas Forklift user interface  not only easy to operate, but also greatly enhance the work efficiency. Time is money, so easy to operate, reliable performance has become the key to improving the competitiveness of these products. High resolution, bright color display can relieve the operator's eye fatigue, rapid conversion of data and reduce the intensity of work.
     A high-precision graphical interface, very demanding on the computer configuration. INTEL company needs at least 500Mhz Pentium Ⅲ series of CPU, and the Windows 98/2000 / NT / XP operating systems. Those vehicle terminal system manufacturers in the development of products, but also take into account the problem of costs, the production of these products are compatible with WindowsCE system, which can greatly reduce the costs associated with the system.

Intelligent truck

Seeking maximum profits, improve operational efficiency is the goal of every business, information systems in an office environment, the role has been well known. Now, the advantage of this positive information technology production lines, warehouses and distribution centers and other field operations expanded and extended environment.
     Site work applications (as well as a variety of operational environments) with unparalleled competitive. If people want their office software, and manufacturing and warehouse management systems together, so mobile, real-time transmission, convenient interface design and other factors will play a key role in the successful implementation. Personnel engaged in the production or storage will not be ready because the so-called "system" reasons to reduce work efficiency, easy to operate, convenient feedback is now a variety of technologies to pursue.
     With bar code technology, wireless LAN technology and data acquisition technology, a field operations system; enterprise management system extends to workers in the palm of your hand or off road rough terrain forklift to make it work more convenient, more intelligent system; wireless vehicle terminal equipment to the truck , guided by the information operations, which is the concept of intelligent all terrain forklifts.

Inspection and maintenance of forklift

Forklift driving before examination

(1) the project in accordance with the provisions, each part of the technical condition of vehicle inspection standard, make the difference between the ten intact.

(2) check the vehicle driving license, driving license and other documents must be running before driving, prohibited the missing card, little card, driving without a license.

Driving

(3) the all terrain forklifts‍ drivers must strictly abide by the "code of conduct internal traffic safety management standards" and "production safety when driving".

(4) should be observed around the situation started before the forklift, (pressure or braking vehicle, brake pressure gauge readings must reach the specified value can be started) to confirm the safety of the whistle to start.

(5) the forklift driving fork bottom height should maintain 300 ~ 400 mm, the door frame must be backward.

(6) forklift at run time, get off to allow any one fork leg, forbidden to stand.

(7) the factory car driving shall not fork lift too high. Import and work site or driving on the way over, should pay attention to whether there is an obstacle scraping

Hit. Forbidden brakes and swerved.

(8) the forklift work, landing must be stable, should use the rope, rope chain firmly closed if necessary. Numerical fork must strictly according to the vehicle load curve specified goods, overloading is strictly prohibited.

(9) the factory fork vehicle travel at more than 7 degrees and is higher than for a speed on the downhill, non special circumstances shall not use the foot brake.

(10) the forklift after parking prohibited goods will be hanging in the air, after the discharge should drop the lifting frame after running.

(11) the forklift fork loading of goods, cargo weight should be the average share in two forks, the goods shall not be skewed, goods should be against the side baffle shelf. Small goods should be put in a set of bins (plate), to prevent from falling. The car contained articles shall not be block the driver's line of sight.

(12) in the process of loading and unloading of goods, must use the brake fork lift truck. If the crane loading and unloading workpieces, the driver must get out of the cab.

(13) the fork in the near or withdrawal of goods, the speed should be slow and steady rolling wheel, pay attention not goods, Dianmu (pallet) and a fork head don't scrape and touch objects support personnel.

(14) in the area of the factory and construction site, no more than ten kilometers per hour, and out of the factory gate, workshop, warehouse and the construction site, no more than 3 kilometers per hour. Forklift driving observed, prevent scratch, wounding.

(15) the car plant in the fork lifting, the lifting frame shall be with the ground forward, not to the lifting frame forward.

(16) the 2.5 tons Diesel forklift trucks‍ lifting or runs, to prohibit any person standing on the fork to control the object or the balance effect. Forklift lifting objects, goods are prohibited in nearby people.

(17) prohibit the use of the fork and other attachments lifting personnel engaged in the work high above the ground and the prohibition of single fork operation or use the fork to the top, pull, prohibit the use of inertia brake is rolling round or easy to roll goods, prohibited methods turn pallet pick use the fork to discharge. The prohibition of high-speed forks goods.

(18) are not allowed in the dock on the shore directly fork shipment goods and not in the train edge direct fork items.

(19) the forklift truck stop the engine idling, should make the mast tilted back. When the engine flameout, should the hoisting sliding frame falls, the fork is placed horizontally on the ground.

(20 factory in the factory, workshop and the construction site of the parking of vehicles, drivers are not allowed to leave the car, such as the need to temporarily leave, must take the key off, the switch pull.

Forklift cars maintenance

(1) maintenance of vehicles, should be the gear lever in neutral, take braking, wheel and supporting mask burdened the sliding frame and protective measures.

(2) clean forklift and crane carriage; fastening screw; check the supplementary fuel, lubricating oil etc..

In addition to the above battery forklift shall comply with the relevant safety regulations for technical operations, and shall also comply with relevant safety regulations for technical operations of battery car.‍

Forklift tire abnormal wear and Prevention

Forklift tire abnormal wear in use in general there are six types: one is the fetal excessove wear; two is the crown two shoulders of abnormal abrasion; three is turned towards the inside tire crown wheel (or lateral) extraordinary partial wear; four is the crown serrated wear; six is the crown of partial wear. Mainly for the uneven tread wear, delamination between plies, loose cord and broken and the resulting matrix cracking. off road rough terrain forklift‍ driving, each part of the tire force is more complex: in a vertical direction of the vertical reaction force, tangential direction is vertical and horizontal reaction force, so that the tire slip existing whole or partial in these directions, cause the tread wear and deformation; tensile, compression in the matrix generated inside caused by fatigue of materials, thus reducing the strength; shear stress is induced in between plies, when the stress exceeds the adsorptive power cord fabric layer and the rubber interlayer, there will be loose cord phenomenon; in the tire deformation, friction heat will occur between the outer tube and inner tube, a part of the heat quantity emitted into the air, another part of the heat accumulation, lead to the decline of tire temperature rise, performance, so that the tire abnormal wear increase, cause the loose cord, broken and matrix cracking. Under certain load and driving conditions, off road forklift trucks‍ tire has a proper tire pressure, when the tire pressure is lower than the standard value when driving, tire radial deformation increases, both sides have excessive deflection, so tread on both sides of the inner wall of the grounding, the side of the tire pressure, tire side wall tension, tire body cord deformation and great alternating stress. Compression deformation of periodic damage, fatigue will return speed cord, tire cord fabric layer and between the tire and the ground is increased relative slip, friction heat increased, the tire temperature rise sharply, reducing the tensile strength of the rubber, loose cord and local delamination, encounter obstacles during impact produced a flat tire. Tread pressure is not uniform, so that the shoulder parts wear serious, leads to the "bridge effect", the tire is dentate or wavy. The tire tread concavity easy embedding road nail and stones, causing mechanical damage. Tire rolling resistance increased, increased fuel consumption. Experiments show that, when the tyre pressure is lower than the standard value of 20%-25%, the corresponding increase in 20% consumption. When the tire pressure is higher than the standard value when driving, the tire crown central ground contact area decreases, the tire and the road surface, load per unit area increased, crown central increased wear. Tyre cord by overdistention, carcass cord stress increases, the fatigue process of cord is accelerated, causing cord pull off, causing early burst tire.‍

‍

Extend the forklift clutch separation method of bearing life

Abstract method to extend the off road forklifts‍ clutch separation bearing life: when considering the repair of mechanical reliability statistical analysis method of domestic CNC machine tool shank standard Mitsubishi heavy industries launched large-scale Longmen type five face machining tool pressure welding technology and new development of differential shell spherical NC cutter design "Dalian machine phenomenon" Reflections on the radius of screw pile machine successfully trial produced new mold molding the processing technology of three hole part programming source bearing failure prediction and prevention of mechanical processing system and the error of aspheric lens grinding and inspection of gear measuring machine related parameters of tool compensation function of the new cam shaft grinding technical analysis of safety light curtain and switch - used in mechanical safety of personal protection god bearing installation method and remove the fast clamping the principle of Russia developed small mobile type wind generator NC drilling machine - milling process life prolonging bearing clutch damage method separating lubricating overflow engine forklift clutch separation bearing life prolonging method of internal combustion forklift clutch bearings working times larger proportion of frequent damage of forklift driver operating properly in time using the left and right bearing maintenance repair to change new the driver technology of water Flat drive forklift almost every separation bearing damage damage affected parts of the clutch lever equipment repair materials Fei Mingxian to improve the clutch.

Method for prolonging forklift clutch separation bearing life

Internal combustion forklift clutch separation bearing work frequently, the damage accounted for a large proportion in the number of forklift driver, if operating properly, timely maintenance, can make the bearing use about 3 months, but in repair is to be replaced. If the driver technology level is low, the driving off road rough terrain forklift‍almost every month there is separation of bearing damage, damage will bring disaster to the other parts, such as the separation of a lever and a clutch plate, thus equipment repair material costs significantly improve.

Causes of clutch separation bearing damaged easily where? In practice, has strict requirements for driver daily separation bearing a drip oil, this is not only tedious operation, and the bearing is often damaged. According to the analysis, due to the high temperature engine isolation bearings, and the bearings of high speed rotating also produces high temperature, under these conditions the oil is very difficult to remain in the bearing and bearing of continuous working in the condition of high temperature, and the lubricating condition is not good, this is the reason for frequent damages.

In view of the above question, also had a bearing test will be heated in the grease, the grease soaked to the bearing, thus treated, although full bearing grease, but due to the destruction of grease structure after high temperature treatment, performance is greatly reduced, the use of this method the effect is not ideal, the service life of the bearing no extension. We also used nose grease gun to the separation bearing direct injection of butter. To install on the bus, after observation of detection, greatly prolong the service life of the bearing. This method of fuel injection get satisfactory results, but the operation is more complicated. And then to explore in the engine apart under the condition of adding butter, first in the 475 C type engine trial success, and again in 480, type 475C and type 492 engine trial, have received very good results. After repeated practice, improvement, sum up experience, has formed a set of relatively simple oiling operation method, the specific process is as follows:

Method of fuel injection (L) engine apart first open the clutch cover, view wear check release bearing, if confirmed bearing without damage or wear not overrun, remove the clutch pedal, an adjusting connecting rod shaft pin, so that the separation of bearing and seat back to last position, with a sharp mouth grease gun to the hole filling grease bearing seat, until the bearing oil overflow, then slightly rotated about bearing oiling, again, repeat the above work, until the bearing are all around a little butter overflow, then the bearing to rotate, observe the amount of oil, such as feeling the rotation of the bearing resistance, prove bearing have been filled with butter. Then remove a little butter separation throughout the overflow of the bearing seat, the pin and the clutch cover re assembled remove.

(2) the oil injection method of disintegration disintegration engine will expose engine fittings separation of the bearing and the bearing seat, small oil using pointed nose grease gun to release bearing seat below the inner hole of the bearing gas, butter overflow when the rotation of the bearing, bearing a lap until butter overflow.

After processing of the above two methods, the separation of gas bearing can no longer within half a year. This set of oiling method in HengShui Railway Station after the trial, mechanical integrity rate increased significantly, has obtained obvious economic benefit. It can save material costs; improve the loading amount, per machine per month can increase the handling capacity of 30t. This method also worked in other railway station promotion, achieved the ideal effect.‍

All terrain forklifts off road rough terrain forklift

Must adhere to the principle of prevention,All Terrain Forklift maintenance usually will be in the end, Wheel Driving Diesel Forklift can effectively prevent the occurrence of the problem before forklift truck maintenance. So to maintenance institutionalized, standardized and scientific efforts to improve the efficient use of forklift trucks. Maintenance divided run-in period and maintenance, forklift routine maintenance, YTO Rough terrain forklift manufacturers seasonal maintenance, storage maintenance and regular care and other five. Today with the running of maintenance based.
Forklift new factory or overhauled within the time prescribed running-job use, known as forklifts run-in period. Internal combustion forklifts run-in period of work is characterized by: Parts machined surface is rough, battery operated forklifts poor lubrication, increased wear, easy to loose fasteners, provisions must be run-in period for maintenance and use in accordance with the internal combustion forklifts.
Run-in period of internal combustion forklifts: Start with 50-hour break-in period.
Run-in period, three tons of internal combustion forklifts from the weight must not exceed 600kg, lifting height is generally not higher than 2m. Speed ??of the engine shall be high speed, speed limiting device shall be adjusted or removed, the speed should be maintained at 12km / h or less. In accordance with the proper use of fuel and lubricants. The right to correct start driving and operating the engine warm-up to more than 40 degrees in order to start; started to have a smooth, until the temperature to normal after an upshift; suitable shift, avoid crashing; choose a good road; try to avoid the emergency brake; Use close attention to the process of transmission, drive axle, wheel wheelchair, brake drum temperature; when loading and unloading operations, strictly abide by the rules.

Off road forklifts Rough terrain forklift refers to the ground without a flat truck loading and unloading operations

 It has a strong off-road capability, good mobility, strong support capabilities. Suitable for loading and unloading,diesel forklift trucks stacking and short demolished the field of materials handling operations.rough terrain forklift for sale Rough terrain forklift has the characteristics of the following aspects of the performance:
1. Power Features:

rough terrain forklifts

Power multi-use internal combustion engines and diesel-based; strong power, high reliability, less failure.
2. Driver Features: Most all-wheel drive; driving force, climbing degree; high speed, maneuverability is good.
3. Transmission characteristics: use more power transmission hydraulic transmission or hydrostatic transmission; handling, through the good.

all terrain forklifts off road rough terrain forklift

Must adhere to the principle of prevention,All Terrain Forklift maintenance usually will be in the end, 3 Ton Lpg Forklift Truck can effectively prevent the occurrence of the problem before forklift truck maintenance. So to maintenance institutionalized, standardized and scientific efforts to improve the efficient use of forklift trucks. Maintenance divided run-in period and maintenance, forklift routine maintenance,battery operated forklifts seasonal maintenance, storage maintenance and regular care and other five. Today with the running of maintenance based.
Forklift new factory or overhauled within the time prescribed running-job use, known as forklifts run-in period. Internal combustion forklifts run-in period of work is characterized by: Parts machined surface is rough, poor lubrication, increased wear, easy to loose fasteners, provisions must be run-in period for maintenance and use in accordance with the internal combustion forklifts.
Run-in period of internal combustion forklifts: Start with 50-hour break-in period.

Off road forklifts Rough terrain forklift refers to the ground without a flat truck loading and unloading operations.

 It has a strong off-road capability, good mobility, strong support capabilities. Suitable for loading and unloading,

YTO Rough terrain forklift manufacturers

 stacking and short demolished the field of materials handling operations.rough terrain forklift for sale Rough terrain forklift has the characteristics of the following aspects of the performance:
1. Power Features: rough terrain trucks Power multi-use internal combustion engines and diesel-based; strong power, high reliability, less failure.
2. Driver Features: Most all-wheel drive; driving force, climbing degree; high speed, maneuverability is good.
3. Transmission characteristics: use more power transmission hydraulic transmission or hydrostatic transmission; handling, through the good.

standardized and scientific efforts to improve the efficient use of all terrain forklifts

 Maintenance divided run-in period and maintenance, forklift routine maintenance, seasonal maintenance, storage maintenance and regular care and other five. Today with the running of maintenance based.
Forklift new factory or overhauled within the time prescribed running-job use,electric forklift truck known as forklifts run-in period. Internal combustion forklifts run-in period of work is characterized by: Parts machined surface is rough, poor lubrication, YTO High Mast Diesel Forklift increased wear, easy to loose fasteners, provisions must be run-in period for maintenance and use in accordance with the internal combustion forklifts.
Run-in period of internal combustion forklifts: Start with 50-hour break-in period.
Run-in period, three tons of internal combustion forklifts from the weight must not exceed 600kg, lifting height is generally not higher than 2m. Speed ??of the engine shall be high speed, speed limiting device shall be adjusted or removed, the speed should be maintained at 12km / h or less.

Off road forklifts known as a field

 is at the airport, docks,battery powered forklifts stations and other road conditions are poor material distribution center materials handling equipment, it has good mobility, cross-country phase reliability.
Terrain forklift truck faster than ordinary, has been developed to 72Mm / h, its maneuverability is obvious;four-wheel rough terrain forklift truck cross country Youwu engine power, all-wheel drive and off-road tires, and thus be able to minister hills, mountains, beaches, sand, snow, ice and mud on the road, with good off-road.

Off road forklifts for sale Rough terrain forklift has the characteristics of the following aspects of the performance:

1. Power Features: Power multi-use internal combustion engines and diesel-based; strong power,

diesel forklift trucks

 high reliability, less failure.
2. Driver Features: Most all-wheel drive; driving force, climbing degree; high speed, maneuverability is good.
3. Transmission characteristics:

YTO Rough terrain forklift manufacturers

 use more power transmission hydraulic transmission or hydrostatic transmission; handling, through the good.

Run-in period of internal off road rough terrain forklift

Start with 50-hour break-in period. Run-in period, three tons of internal combustion forklifts from the weight must not exceed 600kg, lifting height is generally not higher than 2m. Speed ??of the engine shall be high speed, speed limiting device shall be adjusted or removed, the speed should be maintained at 12km / h or less. In accordance with the proper use of fuel and lubricants. The right to correct start driving and operating the engine warm-up to more than 40 degrees in order to start; started to have a smooth, until the temperature to normal after an upshift; suitable shift, avoid crashing; choose a good road; try to avoid the emergency brake; Use close attention to the process of transmission, drive axle, wheel wheelchair, brake drum temperature; when loading and unloading operations, strictly abide by the rules.

off road rough terrain forklift Maintenance

Must adhere to the principle of prevention, maintenance usually will be in the end, can effectively prevent the occurrence of the problem before forklift truck maintenance. So to maintenance institutionalized,off road rough terrain forklift standardized and scientific efforts to improve the efficient use of forklift trucks. Maintenance divided run-in period and maintenance, forklift routine maintenance, seasonal maintenance, storage maintenance and regular care and other five. Today with the running of maintenance based.
Forklift new factory or overhauled within the time prescribed running-job use, known as forklifts run-in period. Internal combustion forklifts run-in period of work is characterized by: Parts machined surface is rough, poor lubrication, increased wear, easy to loose fasteners, provisions must be run-in period for maintenance and use in accordance with the internal combustion forklifts.

Plus extensive distribution network all terrain forklifts

 with the advantages of foreign brands do not have. And because exports frustrated, exports dropped significantly, many domestic brands began to pay more attention to the domestic market, efforts to develop the domestic market, but also created its glory in the domestic market. Future development may affect the forklift truck market constraints, still out of the intensity and the way the government macro-control. Government in recent years has been committed to developing high-tech industry and the tertiary industry services, the overall direction should be no change, but the current revitalization of the economy for the short-term requirements, and has slowed. China's economy there are still many uncertainties, but also has many problems, the economic crisis is not completely over. How short-term growth from investment-led, demand-pull into a long-term growth; how to control the size of credit; unhealthy economic structure adjustment, these same places also restricts the development direction and speed forklift industry. Can be said that China's total demand in the past two years the forklift will have relatively high growth, mainly driven by the power comes from the Wheel Driving Diesel Forklift, which is China's global manufacturing plants by the position will not change in the short term due to .

all terrain forklifts ready to work before use

checking the whole car oil, water leaks phenomenon, lubricate the entire vehicle each lubrication points, check the tire pressure and wheel bearing tightness, check the steering wheel toe, Wheel Driving Diesel Forklift steering angle and steering systems for each component connections, check the adjustment of the clutch and brake pedal free travel and parking brake lever stroke operation, inspection braking performance brakes, check and adjust V-belt tightness, check the battery electrolyte level, density and load voltage, check the engine oil, gear oil, hydraulic oil, coolant fluid levels, check the instruments, lighting, signal , switch button and vehicle accessory equipment operating conditions, check the hydraulic system distribution valve lever travel and work tank trip, check and adjust the tightness of lifting chain, check the door frame, fork work. Prime mover is the engine of internal combustion forklifts, high engine speed, low torque, and can not be reversed. The forklift when the job requires a lower speed, and to constantly changing direction of travel, wheels also have a large torque, for between the prime mover and a drive wheel, a set of prime mover can reduce speed and increase torque and steering means for converting the drive wheels, called the transmission.

Off road forklifts tire features

 multi-use low-voltage, wide-based, off-road tread pneumatic tires; adhesion, good shock absorption performance, without finishing the job on the natural ground such as sand land under muddy ground, snow and other conditions operations. Working device can meet a variety of attachments jobs, such as forks, boom, Drum Lifter, buckets, etc.; can also be used in different ways leveling. Tread width, wheelbase length, good stability; minimum ground clearance, approach and departure angles are larger, good off-road performance.

Off road forklifts Suitable for loading and unloading

Rough terrain forklift refers to the ground without a flat truck loading and unloading operations. It has a strong off-road capability, good mobility, strong support capabilities. Suitable for loading and unloading, stacking and short demolished the field of materials handling operations.Rough terrain forklift has the characteristics of the following aspects of the performance:
1. Power Features: Power multi-use internal combustion engines and diesel-based; strong power, high reliability, less failure.
2. Driver Features: Most all-wheel drive; driving force, climbing degree; high speed, maneuverability is good.
3. Transmission characteristics: use more power transmission hydraulic transmission or hydrostatic transmission; handling, through the good.